New Home Rebate Application

Company

This field is for validation purposes and should be left unchanged.

Program Requirements

*as per 2021 International Energy Conservation Code (IECC)

Walls

Wall Insulation: R-16 minimum*

Mass Wall: R-8*

Basement Wall Insulation: R-0

Crawl Space Wall: R-0

Knee Walls: R-16 minimum (air barrier required)

Duct Work

If supply & return outside of thermal envelope: R-8

Ducts in floor trusses outside of thermal envelop: R-6

Building cavities not used as supply ducts; no duct tape

Mastic & mesh or U1-181a aluminum tape

Exhaust Systems

Outdoor air intakes & exhausts have automated gravity dampers to close when system not in operation

Heat Pump Sizing Performance

Heat Pump: Manual JCalc or other approved Heating/Cooling Methods in accordance with section M1401.3 or 2020 IRC. All other Heating/Cooling systems must meet 2021 IECC

Air Source: Seer 15, HSPF 8.2 or greater

Ground Source: closed

Loop: Cop 3.3 (heating), Eer 14.1 (cooling)

Open Loop: Cop 3.6, Eer 16.2

Attic Insulation & Ventilation

Insulation: R-49 minimum

Vented W/1 Ft2 per 150 Ft2 ceiling area*

Conditioned attics allowed; insulation not required to be air impermeable

No interior vapor retarders installed on ceiling side (attic floor) of unvented attic assembly

Floor Insulation & Ground Cover

Insulation: R-14

Ground Cover: 6-mil vapor barrier tapped at all joints, 6" overlap

Concrete Slab: R-0

Insulation maintains contact with underside of sub floor

Water Heater

Tankless water heaters prohibited.

All electric (mandatory)

50 gallon unit = .94 Ef.

Model Number

Serial Number

Energy Factor Rating

Size in Gallons

Doors

Metal insulated (exception for entry)

Insulated Metal: U-0.6, Wood U-0.5

Insulation, nonmetal edge, max 45% glazing, any glazing double pane U-0.35

Pipes

Circulation hot water pipes R-3, manual off switch

Mechanical system piping >105F or <55F: R-3*

Air Infiltration Control

All joints, seams & penetrations

Site-built windows, doors & skylights

Openings between window & door assemblies, & respective jambs & framing

Utility penetrations & other sources of infiltration

Dropped ceilings or chases adjacent to thermal envelope

Walls & ceilings separating a garage from conditioned spaces

Behind tubs & showers on exterior walls; common walls between dwellings; knee walls

Other Requirements

Can Lights: lc-rated; air tight

Fenestration Glass: U-0.55* maximum

Skylight: U-0.55*

Glazed Fenestration: 0.4 (up to 15 Ft2 exempt) total area not to exceed 18% - waived with performance path*

To receive the rebate: Submit Rebate Program application with name and signature of builder to verify the above-mentioned requirements and procedures, proof of completed installation in accordance to recommended procedures & standards (i.e. pictures, receipts) .

Member Information

Member Name(Required)

First Last

Account Number(Required)

Billing Address(Required)

Street Address City State ZIP Code

Service Address(Required)

Same as previous

Street Address City State ZIP Code

Home Phone Number(Required)

Cell Phone Number(Required)

Square Footage of the Home(Required)

By signing this form, the home builder/developer and the home member agree that the home is built in accordance to the MidSouth Energy Home standards as stated in this application. Homeowners and/or home builder(s) understand that MidSouth Electric reserves the right to conduct inspections prior to issuance of the rebate.

Member Signature (Full Name)(Required)

Home Builder Name(Required)

First Last

Rebate Amount Requested(Required)

Terms & Conditions

Application

Program Requirements

Member Information